
Case Study: Urgent Care Clinic Electrical & Life-Safety in 6 Days
How we turned an architectural set into a permit-ready electrical and NFPA 72 fire-alarm package for a 6,400 sq ft urgent care — in six business days.
Challenge: A Clinic That Could Not Wait
A healthcare developer needed a 6,400 sq ft urgent-care fit-out through permit fast. The program was code-critical in a way a standard office TI is not: dedicated and isolated power for medical equipment, complete egress and exit lighting tied to the life-safety plan, and a full NFPA 72 fire-alarm design with battery and voltage-drop calculations. Their in-house engineer would stamp the set — but had no bandwidth to draft it, and the lease clock was already running.
Urgent care is a demanding occupancy for electrical design. Exam rooms carry receptacle densities and dedicated circuits that a standard office plan never sees. Imaging and lab equipment need isolated-ground circuits and clean power. The waiting and triage areas need lighting that is bright, comfortable, and fully on the emergency system. And the fire alarm has to cover a space where patients may be immobile — notification, audibility, and the sequence of operations all get scrutinized harder than in a typical commercial shell.
Solution: Full Electrical and Fire-Alarm Package in 6 Days
We took the architectural floor and reflected-ceiling plans and produced the complete electrical construction set in 2D AutoCAD, drafted to the firm's CAD standard so their engineer could redline and stamp without cleanup:
- Dedicated and isolated circuits for exam and imaging equipment, with isolated-ground receptacles and home runs that kept medical loads separate from general loads.
- Power and receptacle plans covering every exam room, the lab, triage, waiting, and back-of-house — device densities matched to the actual equipment list, not a generic office template.
- Egress and exit lighting coordinated to the life-safety plan, with emergency fixtures and exit signs circuited to the emergency source and shown on dedicated life-safety sheets.
- Fire-alarm device layout with candela ratings and spacing verified per NFPA 72, SLC/NAC circuiting drawn and tagged, and a riser diagram tying every device back to the panel.
- Battery and voltage-drop calculations backing the fire-alarm design — standby and alarm loads totaled, battery sized, and the longest NAC run verified for voltage at the last device.
- Panel schedules and a coordinated single-line diagram, built from the same load data so the two sheets agreed exactly.
Coordination That Made It Stamp-Ready
Two things made the set land cleanly with the stamping engineer. First, everything was drawn on the firm's title block, layer standard, and symbol library — the deliverable looked like their own production, because it was built to their spec. Second, the fire alarm system design and the electrical scope were drafted as one package, not two: device addresses on the floor plans matched the riser, the riser matched the battery calc, and the candela schedule matched the plans. That internal consistency is what lets an engineer stamp someone else's drafting with confidence.
The lighting scope — general, exam, and egress — was laid out as a coordinated lighting design with fixture schedules and controls, so the clinic's lighting read as one system rather than three overlapping ones.

Results
| Metric | Result |
|---|---|
| Turnaround | 6 business days |
| Review submissions | 1 — cleared on first submittal |
| Revisions used | 2 (included in scope) |
| Stamp-ready | Yes — engineer stamped without redrafting |
| Fire alarm basis | NFPA 72, with battery and voltage-drop calcs |
| Building area | 6,400 sq ft |
The set went to the AHJ and cleared on the first submission. The two review comments — both minor, both about labeling — were resolved inside the included revision window without touching the design.
The Pattern Since
The developer has since sent three more clinic locations through the same pipeline: same CAD standard, same electrical system design and single-line diagram structure, adapted per site. The first location took six days; the repeat locations take less, because the template is proven and the stamping engineer already trusts it.
Healthcare drafting rewards studios that treat life-safety scope with the same rigor as power scope. If your clinic, dental, or medical office needs a permit-ready electrical and fire-alarm package your engineer can stamp, request a quote — send the architectural plans and the equipment list, and we will scope the full set.
Need similar drawings?
Get permit-ready electrical drawings for your project
Send us your plans and scope — we'll come back with a fixed price and a turnaround date. No obligation.
Keep reading
Related articles
ElectricalElectrical Room Layouts That Pass Plan Review
Electrical rooms collect more plan-review comments than almost any other space. Here is how we lay out clearances, dedicated space, and egress to NEC…
ElectricalEV Charging Permit Drawings: What AHJs Want to See
EVSE additions are one of the fastest-growing permit categories. This is the drawing package AHJs expect: 125-percent load calcs, panel schedules that…
Electrical7 Panel Schedule Mistakes That Trigger Plan-Review Corrections
Seven panel-schedule errors that reliably trigger correction letters — mismatched breakers, missing AIC ratings, load totals that do not tie — and how…
Get a fixed drafting quote in under 24 hours
Send us your architectural plans and scope. We'll come back with a fixed price and a turnaround date — no obligation.
