Drafting Studio

Fire Protection

Standpipe System Drawings for Mid-Rise Buildings

Mid-rise buildings live in the standpipe gray zone: tall enough to need one, varied enough that the class and layout are never obvious. Here is what we…

Sep 17, 2026 9 min read
Standpipe System Drawings for Mid-Rise Buildings

What Goes on the Permit Set

A standpipe permit package has three parts: floor plans showing every hose connection location, a riser diagram showing the full vertical distribution with valves and drains, and details covering the fire department connection, hose valves, and pressure-regulating devices. The calculations behind it, flow and pressure per NFPA 14, belong in the submittal too, but the drawings are what the reviewer marks up first.

The floor plans locate each hose connection by stair and floor, with the valve symbol, outlet size, and the elevation of the landing it serves. The riser diagram is the system's portrait: every riser from the supply to the roof, drawn in schematic elevation, with sectional valves, check valves, drains, vents, pressure-regulating valves and their set points, and the FDC tie-in. The details are the close-ups the installer builds from — the FDC assembly, the hose valve installation height and clearances, the PRV station piping. Keep the three parts in agreement: a valve that appears on the riser must appear on the floor plan, and a set point on the riser must match the detail. Reviewers cross-check, and mismatches are the easiest redlines they will ever write.

Where the Code Requires Standpipes

Before drawing anything, confirm the trigger. IBC Section 905 requires standpipes in the occupancies and configurations where firefighters cannot reasonably fight a fire from the ground, and the common triggers for mid-rise work are:

TriggerTypical requirement
Highest story floor more than 30 ft above the lowest level of fire department vehicle accessClass I standpipe
Building with floor levels used for human occupancy more than 30 ft below that access levelClass I standpipe
Covered mall buildingsClass I, with outlets positioned for the mall layout
Stages over 1,000 sq ftClass I or III per the stage provisions
Helistops on rooftopsPer the heliport provisions, coordinated with the fire official

The 30-foot rule is the one that catches mid-rise projects: a four-story building on a sloped site can trip it on the downhill side while looking compliant from the street. We verify the measurement against the civil grading plan, not the architectural rendering, and we document the code section on the cover sheet so the reviewer sees the analysis before the drawings. Where the local amendment lowers the threshold — and several major cities do — the amendment governs.

Class I, Class II, or Class III

The class determines the hardware on every floor. Class I systems provide 2-1/2-inch hose connections for fire department use and are the standard choice for most mid-rise buildings required to have standpipes. Class II systems provide 1-1/2-inch hose stations for trained building occupants and appear in specific occupancies where the code calls for them. Class III systems provide both, giving the fire department its 2-1/2-inch outlets and occupants their 1-1/2-inch stations from the same riser.

We confirm the class with the code analysis before drawing a single valve, because changing classes mid-project means reworking every floor plan, the riser, and the details.

The class also drives the pressure requirements the drawings must state. NFPA 14 caps static pressure at 175 psi anywhere in the system and limits residual pressure at 1-1/2-inch occupant outlets to 100 psi — which is exactly why Class III systems so often need pressure-regulating valves on the occupant connections in taller buildings. The class decision, the PRV decision, and the hydraulic calc are one conversation, and it happens before the first floor plan is drawn.

Sizing the Riser and the Hydraulics Behind It

The riser diagram tells a story the reviewer can verify against NFPA 14's demand numbers. For hydraulically designed Class I and Class III systems, the standard demand is 500 gpm at the hydraulically most remote standpipe, plus 250 gpm for each additional standpipe, up to a maximum of 1,250 gpm — reduced to 1,000 gpm where the building is fully sprinklered. The system must deliver 100 psi residual at the outlet of the most remote 2-1/2-inch hose connection while flowing that demand.

Those two numbers — the gpm total and the 100 psi residual — size everything on the riser. Minimum pipe sizes follow from the flow: hydraulically designed standpipes typically draw at 4-inch minimum for the risers themselves, with larger feed mains where the calc demands it, and the diagram must show the size at every segment so the reviewer can trace the hydraulics visually. Where static pressure exceeds 175 psi — common in the lower floors of anything over about six stories, depending on the supply — pressure-regulating valves go on the diagram with their set points, and the detail shows the PRV station: inlet and outlet gauges, the bypass arrangement, and the test connections the AHJ will want to see at acceptance. The calc report behind the drawing carries the node-by-node proof; the drawing carries the verdict.

Riser Details That Matter

The riser diagram shows each standpipe riser from the water supply to the roof manifold, with sectional control valves, check valves, drain risers, and air vents at the high points. Every hose connection gets a symbol with its size and floor elevation. Where the hydraulics require it, we show pressure-regulating valves with their set points, because NFPA 14 caps static pressure at 175 psi and limits residual pressure at 1-1/2-inch occupant outlets to 100 psi.

A riser diagram that omits drains and vents will still get approved, and then the installing contractor will ask where they go. We would rather answer that question on the drawing.

Two more details that separate a buildable riser from a merely approvable one. First, the sectional control valves: NFPA 14 wants the system arranged so a single riser can be isolated without taking down the whole building, and the diagram should make the isolation boundaries obvious — a contractor who has to guess which valve to close during a repair will guess wrong. Second, the roof manifold: where required, the diagram shows the manifold with its hose connections, the check valve arrangement, and the vent, because the roof is the last place anyone wants a field interpretation.

A standpipe hose valve in a stairwell, the firefighter connection every mid-rise riser drawing must locate.
A standpipe hose valve in a stairwell, the firefighter connection every mid-rise riser drawing must locate.

Hose Connection Placement

Hose connections go at each floor level and intermediate landing of every required stairway, positioned so firefighters can stretch hose to any point on the floor. The practical test we draft to: no portion of the floor area should be beyond a reasonable hose lay from a connection, and the AHJ will apply its own interpretation of reasonable. We also show the roof manifold where required, with the connections the fire department expects to find there.

On the floor plan, each connection gets the full treatment: the valve symbol at the stair landing it serves, the outlet size, the landing elevation, and the clearances around it. Hose valves mount roughly 3 to 5 feet above the landing — high enough to connect a charged line without kneeling, low enough to reach under stress — and the detail states the mounting height so the installer doesn't improvise. We keep the valve clear of the door swing and the handrail, dimensions the clear space on the plan, and coordinate with the architect where the stair is tight. A valve the firefighter can't reach quickly is a design failure the calc can't fix.

Stairwell and Roof Details Reviewers Check

Beyond the valve locations, reviewers walk the stair mentally and check the details that affect operations. The stair identification signage at each hose connection — which stair, which floor — goes on the plan as a note, because a firefighter on the third floor of Stair B needs to know they're at Stair B. Where standpipes run in the stair enclosure, the pipe routing must not reduce the required egress width; we dimension the remaining clear width at the tightest point. On the roof, the manifold detail shows the hose connections with their caps and chains, the check valve, and the vent termination, plus the access path the fire department will use to reach it. And the signage package — FDC signs, stair signs, PRV tags — gets its own note block, because the AHJ that can't read the system from the signs will make you prove it some other way.

FDC Placement and Access

The fire department connection must be visible and accessible from the street front or another approved location, with signage the responding crew can read from the apparatus. We show the FDC on the site plan and the building elevations, coordinate its location with the civil grading so it is not buried behind landscaping, and detail the check valve arrangement behind it. An FDC the fire department cannot find quickly is a design failure no calculation can fix.

The FDC detail is one of the most-reviewed sheets in the package. It shows the connection type and size, the check valve and any pressure-regulating arrangement behind it, the signage with the system it serves, and the clearances in front of it — typically kept clear of parking, dumpsters, and anything a responding engine can't move. We show the FDC's relationship to the fire department access road on the site plan and dimension the hose-lay distance, because some AHJs measure it. Where the building has multiple standpipe zones, each zone's FDC is labeled for its zone; an unlabeled FDC on a zoned building is a guaranteed correction.

Common Plan-Review Corrections

The redlines on standpipe packages are remarkably consistent. Missing or unlabeled PRV set points on the riser. Hose connections shown on the floor plan but not on the riser, or vice versa. No drain riser shown. The FDC detailed but not located on the site plan. Static pressure above 175 psi with no pressure regulation. The 100 psi residual requirement stated for the wrong outlet or missing from the notes. And the perennial favorite: the riser diagram's pipe sizes don't match the hydraulic calc's pipe sizes. We run a three-way check before issuing — floor plans against riser, riser against calc, details against both — because every one of these corrections is a coordination failure, and coordination is what the drawing set is for.

Pressure, Testing, and the Notes Block

Our drawing notes state the required residual pressures, the hydrostatic test pressure of 200 psi held for two hours, and the flow test procedure. These notes are not decoration. They tell the reviewer the system was designed to NFPA 14 end to end, and they give the installing contractor the acceptance criteria before the pipe goes in the wall.

We draft standpipe packages as part of our sprinkler layout scope — floor plans, riser diagrams, and FDC details — coordinated with the building's fire alarm system where the AHJ wants both. Request a quote with your floor plans and water supply data.

Share

Need similar drawings?

Get permit-ready fire protection drawings for your project

Send us your plans and scope — we'll come back with a fixed price and a turnaround date. No obligation.

Get a fixed drafting quote in under 24 hours

Send us your architectural plans and scope. We'll come back with a fixed price and a turnaround date — no obligation.