Commercial Electrical Load Calculation: Step-by-Step NEC Guide
Commercial load calculations punish guesswork: lighting, receptacles, kitchen equipment, and HVAC each carry their own demand factors. This…

Commercial electrical load calculations are where residential rules of thumb go to die. A restaurant, an office, or a retail space mixes lighting, receptacle, motor, kitchen, and HVAC loads that each follow different NEC Article 220 demand rules — and the plan reviewer will check every one of them. This guide walks the standard method for non-dwelling occupancies step by step, works a complete restaurant example with real numbers, and covers the optional methods the code allows when the standard path does not fit.
Why commercial calculations are a different animal
In a dwelling, the code hands you generous demand factors because residential loads are diverse by nature — not every appliance runs at once. Commercial occupancies get no such charity. Under 220.42, most non-dwelling occupancies take their general lighting load at 100 percent, because in a restaurant or office the lights genuinely are all on at the same time.
The stakes are also higher. An undersized commercial service means a main breaker trip during Friday dinner service or a failed inspection that delays a certificate of occupancy. An oversized one means thousands of dollars in switchgear, conductors, and utility charges for capacity nobody uses. The calculation is the document that keeps both outcomes off the table.
In commercial work, the load calculation is a financial document as much as an engineering one — it sizes the most expensive equipment in the building.
The standard method for non-dwelling occupancies
The standard method lives in 220.40 through 220.61, and the sequence for a commercial building looks like this:
- Compute general lighting from Table 220.12 using the occupancy type and floor area
- Add receptacle loads at 180 VA per outlet (220.14) and apply the 220.44 demand
- Add fixed multi-outlet assemblies, signs, and show-window lighting per 220.43 and 220.44
- List motors and take 125 percent of the largest motor (220.50, Article 430)
- Add commercial cooking equipment with Table 220.56 demand factors
- Add HVAC at 100 percent of the largest system — heating or cooling, never both (220.60)
- Total the volt-amperes, divide by the system voltage, and select the service size
The single biggest conceptual shift from residential work: each load category keeps its own identity all the way to the total. You do not blend lighting and receptacles into one "general" number the way the dwelling methods do.
Demand factors that actually move the number
Four demand rules do most of the work in a commercial calculation:
Lighting (Table 220.12 and 220.42). The volt-amperes per square foot come from Table 220.12 by occupancy — a restaurant dining area is 2 VA per sq ft, for example. Then 220.42 applies: dwelling units, hospitals, hotels, and warehouses get reduced demand factors, but nearly every other commercial occupancy takes lighting at 100 percent.
Receptacles (220.44). The first 10 kVA of receptacle load counts at 100 percent; everything above that counts at 50 percent. On a receptacle-heavy occupancy this single rule can shave 20 percent off the service size, so count your outlets carefully — 220.14(I) values each receptacle at 180 VA.
Motors (220.50). Take 125 percent of the full-load current of the highest-rated motor, plus 100 percent of the rest. For HVAC-heavy buildings this adder is significant, and it applies to the largest motor in the entire calculation, not per system.
Kitchen equipment (Table 220.56). Commercial cooking equipment gets its own demand table based on the number of units: six or more pieces of equipment may be calculated at 65 percent of the connected load. This is the rule that keeps restaurant services sane — without it, every fryer, oven, and warmer at nameplate would demand absurd service sizes.

Worked example: a 3,000 sq ft restaurant, 208Y/120V three-phase
Consider a 3,000 sq ft restaurant with a dining room, a commercial kitchen with six pieces of electric cooking equipment, a 10-ton rooftop unit, and an illuminated sign.
General lighting. 3,000 sq ft × 2 VA per sq ft (Table 220.12, restaurants) = 6,000 VA. Restaurants fall under "all others" in 220.42, so demand is 100 percent: 6,000 VA.
Receptacles. Sixty duplex receptacles × 180 VA = 10,800 VA. Per 220.44: the first 10,000 VA at 100 percent = 10,000 VA; the remaining 800 VA at 50 percent = 400 VA. Demand total: 10,400 VA.
Kitchen equipment. Fryer 12 kW, convection oven 9 kW, range 10 kW, food warmer 3 kW, dishwasher booster heater 6 kW, mixer 2 kW — six units totaling 42 kW. Table 220.56 permits 65 percent for six or more units: 42,000 × 0.65 = 27,300 VA.
HVAC. The 10-ton rooftop unit nameplates at MCA 45 amps. At 208 volts three-phase: 45 × 208 × 1.732 = 16,211 VA, taken at 100 percent: 16,200 VA.
Sign. One electric sign per 220.43(A): 1,200 VA.
Largest motor. The RTU compressor is the largest motor at roughly 30 amps: 30 × 208 × 1.732 × 25 percent = 2,700 VA.
Total: 6,000 + 10,400 + 27,300 + 16,200 + 1,200 + 2,700 = 63,800 VA. Divide by (208 × 1.732 = 360.3): 177 amperes.
The minimum code-legal service is 200 amps, the next standard size above 177. In practice, most restaurant owners approve a 400-amp service here — the incremental cost of the larger gear is small compared to the cost of a second service upgrade when the menu (and the kitchen equipment list) grows.
A note on the neutral: 220.61 permits a reduced neutral calculation based on maximum unbalanced load, but in a three-phase wye system serving significant nonlinear kitchen and lighting loads, engineers frequently keep the neutral at full size. Document whichever choice you make.
When you may use the optional methods
The standard method is always permitted, but Article 220 Part IV offers alternatives for specific situations:
Existing buildings (220.87). If the building has 12 months of recorded maximum demand data — typically from the utility, in 15-minute intervals — you may calculate the existing load at 125 percent of that peak plus 100 percent of all new loads. This is the fastest legitimate path for tenant improvements and additions, but the data must be real: estimated or extrapolated demand does not qualify.
Schools (220.86). New schools get their own simplified VA-per-square-foot method, which usually produces a smaller service than the standard calculation.
New restaurants (220.88). All-electric kitchens and not-all-electric kitchens each get prescribed volt-amperes per square foot applied separately to kitchen and dining areas. It is purpose-built for exactly the occupancy in our example, and it is worth running as a cross-check — the code lets you use whichever method you prefer.
Run the optional method as a cross-check even when you submit the standard one. If the two answers disagree wildly, one of them has an arithmetic error.
Mistakes that stall commercial permits
The errors we correct most often on commercial submittals: applying dwelling demand factors to commercial occupancies, counting both heating and cooling in 220.60, omitting the 125 percent largest-motor adder, sizing the service from the panel schedule total instead of the calculated demand load, and submitting a calculation with no stated method. A reviewer who cannot tell which Article 220 part you used will assume the worst and ask for a resubmittal.
Another quiet killer is the receptacle count. Designers routinely underestimate outlets in dining and retail spaces, and 180 VA per receptacle adds up fast. Walk the floor plan and count honestly — the reviewer will.
What a permit-ready calculation package looks like
A commercial electrical submittal that sails through review contains the load calculation with the method and every code section labeled, panel schedules whose demand columns match the calculation, a riser or single-line diagram showing the service size the math justifies, and an electrical system design narrative tying the numbers to the actual equipment. When all four agree, the electrical review becomes a formality.
Our electrical load calculation service delivers exactly that package — stamped calculations, coordinated panel schedules, and permit-ready drawings for restaurants, retail, offices, and mixed-use buildings nationwide. Upload your plans at /request-quote and get a fixed-fee proposal within one business day.
Need similar drawings?
Get permit-ready electrical drawings for your project
Send us your plans and scope — we'll come back with a fixed price and a turnaround date. No obligation.
Keep reading
Related articles
ElectricalElectrical Room Layouts That Pass Plan Review
Electrical rooms collect more plan-review comments than almost any other space. Here is how we lay out clearances, dedicated space, and egress to NEC…
ElectricalEV Charging Permit Drawings: What AHJs Want to See
EVSE additions are one of the fastest-growing permit categories. This is the drawing package AHJs expect: 125-percent load calcs, panel schedules that…
Electrical7 Panel Schedule Mistakes That Trigger Plan-Review Corrections
Seven panel-schedule errors that reliably trigger correction letters — mismatched breakers, missing AIC ratings, load totals that do not tie — and how…
Get a fixed drafting quote in under 24 hours
Send us your architectural plans and scope. We'll come back with a fixed price and a turnaround date — no obligation.
